calculate-loan

01 Loan payments

Vehicle Coast Down Equation and Calculator

Calculator No. 01-15352 · Updated · Formula and assumptions shown below

Average resisting force 834.0 N
Average deceleration
0.556 m/s^2
= (initial speed − final speed) ÷ elapsed time
Average power lost
20,850 W
= Average resisting force × (initial speed + final speed) ÷ 2
Vehicle mass
1500 kg
Input
You enter
Vehicle mass (kg), Initial speed (m/s), Final speed (m/s), Elapsed time (s)
You get
Average resisting force (N), Average deceleration (m/s^2), Average power lost (W)
Rounding
1 dp · 3 dp · 0 dp

Estimate for education, not financial advice. The result follows from the numbers you enter and the formula shown. It is not a quote or an offer, and it does not include fees, taxes or insurance unless the calculator asks for them. Ask your lender for the exact figures.

The vehicle coast down equation estimates the force resisting a vehicle as it rolls without engine power, using its speed loss over time. Enter vehicle mass, two speeds, and the time between them to calculate average deceleration and resistance force; the result is an estimate, not a full road-load test.

Formula

For a vehicle slowing from speed v1 to speed v2 over elapsed time t, average deceleration magnitude is a = (v1 − v2) / t. Newton’s second law gives the average net resisting force: F = m × a, or F = m × (v1 − v2) / t. Here m is vehicle mass in kilograms, speeds are in metres per second, t is in seconds, a is in metres per second squared, and F is in newtons. The calculator also estimates average power dissipated as P = F × v̄, where v̄ = (v1 + v2) / 2; P is in watts. This power estimate assumes speed falls uniformly over the interval.

These equations use positive values for a slowdown: the initial speed must be higher than the final speed. The input limits prevent negative speeds but do not enforce that ordering, so enter the speeds in the correct order. Equal or reversed speeds do not represent the coast-down condition modelled here.

Worked Example

Using the calculator’s default values: mass = 1,500 kg, initial speed = 27.78 m/s, final speed = 22.22 m/s, and elapsed time = 10 s.

  1. Speed loss: 27.78 − 22.22 = 5.56 m/s.
  2. Average deceleration: 5.56 / 10 = 0.556 m/s², displayed to three decimal places.
  3. Average resisting force: 1,500 × 0.556 = 834 N, displayed to one decimal place.
  4. Average speed: (27.78 + 22.22) / 2 = 25 m/s.
  5. Average power lost: 834 × 25 = 20,850 W, displayed to the nearest watt.

The force calculation uses the unrounded deceleration, 5.56 / 10 = 0.556, so its displayed result is 834.0 N. The power output follows the displayed calculator expression and equals 20,850 W.

What a Coast-Down Test Measures

A coast-down test records how quickly a vehicle loses speed after the powertrain stops driving the wheels. It is used to estimate road-load resistance: the combined effect of aerodynamic drag, tire rolling resistance, and other mechanical losses. The measured slowing is not caused by one factor alone.

At a given moment, the vehicle’s longitudinal motion can be described by m × a = Fnet. During a coast, the net force points opposite the direction of travel. The calculator reports the magnitude of that average opposing force across the selected speed interval. For a detailed test, engineers collect speed and time data over a broader range and fit a road-load model rather than treating resistance as one constant.

What the Result Means

A force result of 834 N means that, averaged across this example interval, about 834 newtons of net force opposed forward motion. It does not mean that aerodynamic drag alone was 834 N, or that the same force applies at every speed. Drag usually changes substantially with speed, while tire, bearing, and drivetrain losses have different dependencies.

The power result describes the rate at which mechanical energy is being lost on average. Since power is force multiplied by speed, the same resisting force consumes more power at higher speed. In the example, 834 N acting at an average 25 m/s corresponds to 20,850 W, or 20.85 kW. This is not fuel consumption: it is mechanical power dissipated during the interval.

Speed Units and Measurement

The calculator requires metres per second. To convert kilometres per hour to metres per second, divide by 3.6; for example, 100 km/h is about 27.78 m/s. To convert miles per hour, multiply by 0.44704; 50 mph is about 22.35 m/s. Use the same unit for both speeds, and make sure mass is in kilograms and time is in seconds.

Coast-down measurements can be affected by road slope, wind, air density, tire condition and pressure, vehicle loading, brake drag, and drivetrain configuration. A slight downhill grade may partly counteract resistance, making measured slowing smaller; an uphill grade can make it larger. Wind changes the air speed relative to the vehicle, so testing in opposite directions or controlled conditions can help separate environmental effects in formal procedures.

Limits and Common Misreadings

  • It is an interval average. If the vehicle loses speed unevenly, the computed acceleration and force average over the chosen time; they do not describe every instant.
  • Mass matters. Force is proportional to the mass entered. Include the vehicle and its actual load when that is the quantity being studied.
  • Grade and wind are included in the observation. This basic calculation cannot identify or subtract those influences.
  • It is not a complete road-load equation. Detailed models often express road load as a speed-dependent combination such as A + Bv + Cv², with coefficients obtained from controlled tests. This calculator does not determine those coefficients.
  • Rounding can affect displayed figures. Calculations use the entered values, while outputs are rounded for display. Avoid rounding speeds or time prematurely when analysing measured data.

A common misconception is that the coast-down equation directly gives the aerodynamic drag coefficient. It does not. Estimating that coefficient requires separating aerodynamic force from other losses and knowing factors such as air density, frontal area, and relative wind speed. The present equation supplies the total average opposing force only.

Frequently Asked Questions

What is the vehicle coast down equation?
For average resisting force, F = m(v1 − v2)/t, where m is mass, v1 and v2 are the initial and final speeds, and t is the elapsed time. Average deceleration is (v1 − v2)/t.

How do I convert km/h to m/s?
Divide the speed in kilometres per hour by 3.6. For instance, 90 km/h is 25 m/s.

Does coast-down force equal aerodynamic drag?
No. The observed force combines aerodynamic drag with rolling resistance and mechanical losses, and can also be affected by road grade and wind.

Why does the calculated force change with speed?
Several resistance components vary with speed. Aerodynamic drag rises roughly with the square of relative air speed, so total road load is generally not constant through a wide speed range.

Can this calculate a vehicle’s drag coefficient?
Not by itself. A drag-coefficient estimate requires additional measurements and a way to isolate aerodynamic drag from other forces.

Related

Formula used
in m | Vehicle mass | kg | 1500 | 0 | 100000
in v1 | Initial speed | m/s | 27.78 | 0 | 200
in v2 | Final speed | m/s | 22.22 | 0 | 200
in t | Elapsed time | s | 10 | 0.001 | 10000
out f | Average resisting force | N | m * (v1 - v2) / t | 1
out a | Average deceleration | m/s^2 | (v1 - v2) / t | 3
out p | Average power lost | W | f * (v1 + v2) / 2 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard loan formula for this calculation, fixed rate and monthly compounding unless stated, rounded as each result states. Not financial advice; no lender, rate or product is recommended. See formulas and assumptions, the disclaimer or report an error.

More in this section

The whole Loan payments section →